Structural Fire Damage Cleaning in Inglis, FL
The drywall is gone, and now you are staring at blackened studs, scorched joists and a charred roof deck. Somebody now has to decide what gets blasted clean, what gets sistered and what gets replaced. Unify Fire Solutions puts you in touch with independent, licensed and insured Inglis contractors who clean the bare structure down to sound wood.
- Soda blasting, dry ice blasting and wire brushing
- Char depth probed member by member
- Cleaned wood encapsulated against lingering odor
What Makes Framing Work Different
Close up the walls over dirty framing and the smoke odor bleeds right back through the new finish. Cleaning the structure is the step that decides whether the rebuild smells like a new house or a campfire.
Licensed & Insured Independent Pros
The contractors we connect you with are independent businesses carrying their own license and insurance. Verify both, and ask whether the crew follows the IICRC S700 standard for fire and smoke work.
Upfront Written Estimates
Blasting is priced by surface area, media and access, and attics and crawlspaces cost more to reach. Ask for a line-item written estimate before the first bag of media is opened.
Rapid Local Dispatch
Day or night, a dispatcher picks up and starts looking for a structural cleaning crew right away. How fast someone arrives depends on availability and distance, often within the same day.
Blasting Rigs and Probing Tools
This trade runs on gear most remodelers do not own: soda blast pots, dry ice blasters, tow-behind compressors, HEPA vacuums, air scrubbers and an awl for probing char.
Stay out of a fire-damaged attic, and never walk a charred roof deck to check it. Burned joists and decking can fail under one person's weight, and open wiring may still carry current. Wait for the contractor to check that the structure is safe, and keep people off floors that sit over a burned crawlspace or basement.
Structural Cleaning Services From Rafters to Slab
Furniture and debris are a separate job. This page is about the framing, masonry and steel that actually carry the load.
Char Depth Probing and Member Decisions
Pressing an awl into the blackened wood shows how deep the char goes; a shallow crust over firm wood usually means it can be cleaned. Deep char that eats into the section of a joist or truss chord means sistering or replacement.
- Members marked clean, sister or replace
- Structural engineer called in for questionable beams, trusses and headers
- Photos of each marked member for the claim
Soda Blasting
Sodium bicarbonate is softer than wood, so it strips soot and light char off studs, joists and roof decking without gouging the grain. It leaves a fine white dust and some residue, so containment and a thorough HEPA vacuum afterward are part of the job.
Dry Ice Blasting
With dry ice the pellets sublimate on impact, so there is nothing left on the floor but the soot itself. It works well in tight attics and around wiring, though it costs more and is noisy.
- Hearing protection and ventilation required
- Good choice when residue would be a problem
Wire Brushing and Sanding
Small, isolated char spots are often handled by hand with wire brushes and sanders tied into a HEPA vacuum. It is slow on big areas but precise where blasting would be overkill.
Brick, Block, Concrete and Steel Beams
Fireplace surrounds, block foundation walls and concrete slabs hold soot in their pores, and alkaline cleaners, scrubbing or blasting pull it out. Steel beams get cleaned and inspected for any heat warping, with doubts sent to the engineer.
Encapsulation and Attic Insulation Removal
Even well-blasted wood can hold faint odor in its pores, so crews roll or spray a pigmented shellac-based or specialty encapsulating sealer over cleaned framing. In the attic, smoke-soaked blown-in or batt insulation is vacuumed out with a high-powered insulation vac before the rafters and decking are cleaned.
Under the house, the crew probes the joists, sill plates and subfloor underside, then blasts and seals what can stay. Expect a vapor barrier to be pulled and replaced if smoke or hose water soaked it.
Have the contractor explain the method they plan for each part of the house. A good crew may soda blast the open walls, dry ice the attic around the wiring and hand sand a few studs near the panel.
Plan for containment, because blasting throws soot and media into every corner it can reach. Expect poly over openings, taped-off HVAC returns and air scrubbers pulling the space under negative pressure during blasting. Ask how they will protect finished rooms and windows that were not damaged.
Bare Framing Covered in Soot and Char?
Ring the dispatch line and we start finding a structural cleaning crew near Inglis. It costs nothing to call.
Call +1-833-336-1630How a Structural Cleaning Job Unfolds
- 1
Phone the Dispatcher
Say which parts of the structure are open now, such as walls, attic, crawlspace, masonry or steel. Mention if a roofer, engineer or adjuster has already been out.
- 2
Mobile Crew on Site
An independent crew shows up with its compressor, blast gear, poly and air scrubbers. First they confirm the roof deck and floors will hold weight and that the exposed circuits are dead.
- 3
Probe, Mark and Quote
Every exposed member gets probed with an awl and marked clean, sister or replace, and anything borderline goes to a structural engineer. A written, itemized quote covering area, blast method, encapsulant and attic insulation comes before any work starts.
- 4
Blasting, Sealing and Walkthrough
Once the wood is blasted, vacuumed and sealed, the crew lead walks you through the open structure. Do a sniff test on a warm afternoon, and ask for photos of every marked member before the rebuild closes the walls.
What Callers Said About Their Structural Crew
The attic fire left every rafter black and the insulation soaked. The crew pulled the insulation, dry ice blasted the rafters and rolled sealer on everything. An engineer looked at two deeply charred rafters and they were sistered instead of torn out.
I assumed every black stud in the hallway had to be replaced. The crew lead probed each one with an awl and showed me that most were just surface char. Soda blasting and a coat of sealer saved most of the wall.
The fire in our lower level left the block walls and the steel beam coated in soot. The contractor cleaned the block and the beam, then had an engineer check the steel for warping. The basement smells normal again, even closed up.
Common Questions About Cleaning Charred Framing
How do crews decide if a charred stud can stay?
The test is simple: they probe it. Push an awl into the char, and if it hits solid wood after a shallow layer, the stud is usually a cleaning job. Members with deep char, splitting or a lost cross section get sistered or replaced, and anything structural in doubt goes to a licensed structural engineer.
What is the difference between soda blasting and dry ice blasting?
Soda blasting uses sodium bicarbonate media that is gentle on wood and helps neutralize odor, but it leaves dust and residue to clean up. Dry ice pellets vanish on impact, so cleanup is easier and it works well around wiring, but it is louder and usually costs more. Many crews use both on the same house.
Why seal the framing if it has already been cleaned?
Wood is porous, and smoke molecules sit deep in the grain where no blasting can reach. A shellac-based or specialty encapsulant locks that residual odor in so it cannot off-gas through the new drywall. Sealing dirty wood does not work, so the cleaning has to come first.
Does the attic insulation have to come out after a fire?
In most cases where smoke got into the attic, it does. Blown-in and batt insulation trap smoke and soot like a filter, and many get soaked by hose water too. Crews vacuum it out with a truck-mounted or portable insulation vac so the rafters and decking can be inspected and cleaned before new insulation goes in.
Can soot be cleaned off brick and concrete block?
Usually yes, though masonry takes more effort than drywall because soot sinks into the pores. Crews use alkaline masonry cleaners and stiff brushes, and soda or other media blasting for heavy buildup. Heat-cracked or spalled block and brick should be looked at by an engineer or mason.
Do I need a structural engineer for fire-damaged framing?
You may not on a small job, but any doubtful load-bearing member calls for one. Trusses, beams, headers, steel and heavily charred joists are where an engineer's letter protects you and helps the claim. Your local building department may also require one before the walls close.
Charred Framing Cleaning Across Inglis and Beyond
Our dispatch line covers Inglis and the nearby communities around it, from older homes with plaster and solid-sawn joists to newer builds with engineered trusses. Attics, crawlspaces, basements, garages and small commercial buildings are all in scope.
- Attic fires
- Electrical fires
- Furnace puff-backs
- Chimney fires
- Lightning strikes
- Neighbor's fire spread
Should the first contractor not suit you, ring us again and we will connect you with a different one. Do not let the rebuild close walls over dirty framing.
